Go Back   The Navara Forum > D40 > D40 Engine

Reply
 
Thread Tools Display Modes

P1021 Fault with Intermittent loss of power
  #1  
Old 22-05-2019, 10:16 PM
51oul 51oul is offline
Junior Member
 
Join Date: Aug 2017
Location: australia
Posts: 13
Default P1021 Fault with Intermittent loss of power

Hi Guys,
been having some very intermittent issues as of late. When the issue is apparent, the vehicle struggles to get beyond 80kms/hr and and seems to rev high into 4th gear before i have to manually shift to 5th (its an auto with the manual selection)

Basically it feels like there is no high end power, cruising around town I cant seem to tell much difference

There is a fault code which keeps popping up p1021 (which is hard to determine but everything is pointing at the turbo actuator). Mine is not a vacuum operated actuator and appears to be the electrical controlled one - correct me if Im wrong. An engine warning light has only appeared once and has been cleared and not reappeared.

As mentioned, the issue appears to be very random, and cannot pinpoint a cause. the few times it has happened, a simple restart of the vehicle has fixed it.

At this stage my regular mechanics have done the best they can and until the issue becomes a bit more apparent or regular, we are just going to keep on going as normal. They said that if the actuator needs replacement, its generally the need for a full new turbo unit which is along the lines of what i have been reading. But im not ready to go down that path yet until the issue is more pronounced. Just after some advice if anyone else has had similar issues or can shed any more light on this?
cheers!

Below is a photo of my actuator unit.
Attached Thumbnails
Click image for larger version

Name:	20190312_072800.jpg
Views:	24
Size:	214.8 KB
ID:	22599  
Reply With Quote
Sponsored Links

  #2  
Old 23-05-2019, 12:56 AM
Old.Tony's Avatar
Old.Tony Old.Tony is offline
Administrator
 
Join Date: Oct 2009
Location: Mid Coast Region, NSW, Australia
Posts: 15,200
My Mood:
Garage
Default

Well, the manual does confirm P1021 is an abnormal operating signal from the turbocharger boost contrller to the ECM. There could be a couple of reasons for this.


1) Poor electrical connection for the actuator. Undo its connection(s), clean, reinstall.


2) Poor battery connections. Unlikely because you'd normally see "random" error codes, but it doesn't hurt to clean the terminals anyway.


3) Poor ECU connection. Very unlikely, but it's free to check/fix - undo, redo, the movement of the plug should give the little tabs a quick clean anyway.


4) Poor signal from other inputs eg MAFS. Also unlikely but also free. Don't stick anything in the hole in the MAFS, just use spray electrical contact cleaner.


5) Failing actuator. When the symptoms appear, pull over and see if the actuator is moving anything while the engine remains idling (don't turn it off when you stop). There were a bunch of these replaced by Nissan as they were faulty from the factory, perhaps you could check and see if yours is one of them that missed out?


The actuator is individually replaceable.
__________________

Check out the FAQs by clicking here!



"Money can't buy happiness, but it does make misery a lot easier to deal with."
Reply With Quote

  #3  
Old 23-05-2019, 11:29 AM
51oul 51oul is offline
Junior Member
 
Join Date: Aug 2017
Location: australia
Posts: 13
Default

thanks for the reply Tony! i'll give these a go and see how we go.
If the actuator does need replacement, where would be the best place to start to source one?

The times i have looked under the hood when the issue was occuring the actuator arm seemed to remain stationary. It only seems to move when the engine is started (it will click over to the engaged position) and then a few seconds after shutdown I'll hear it flick back. I think the vacuum controlled ones had a bit of a wobble or something on them during operating, but never knew mine to do that, unless i've never noticed (completely possible) i'll keep an eye on it tho!

thanks again

Last edited by 51oul; 23-05-2019 at 11:37 AM. Reason: added more info
Reply With Quote

  #4  
Old 23-05-2019, 12:55 PM
Old.Tony's Avatar
Old.Tony Old.Tony is offline
Administrator
 
Join Date: Oct 2009
Location: Mid Coast Region, NSW, Australia
Posts: 15,200
My Mood:
Garage
Default

Try this on eBay (check your turbocharger model number on the turbo). They're around, even if they're named wrong. The correct name on that link is in the middle of the page.


Get someone to sit in the car and rev the engine while you watch. The turbocharger should move the vane a little when that is done. It shouldn't do it a lot, because the ECU will know you're not in gear and moving, so it won't command the turbo to full power.
__________________

Check out the FAQs by clicking here!



"Money can't buy happiness, but it does make misery a lot easier to deal with."
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT +1. The time now is 10:06 PM.



Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
| Home | Register | FAQ | Members List | Calendar | Today's Posts | Search | New Posts |